×

Klik hier voor
Inhoudsopgave

menuSnelstartgids USW-24

Inhoud van verpakking

UniFi Switch
Beugels voor rekmontage (2 stuks)
Beugelschroeven (8 stuks)
Montageschroeven (4 stuks)
Kooimoeren (4 stuks)
Netsnoer

Systeemvereisten

BELANGRIJK: Het wordt ten zeerste aangeraden UPS-back-up- en stroomvoorschriften te gebruiken om schade aan apparatuur als gevolg van stabiliteitsproblemen met lokale netvoeding te voorkomen.

Hardware-overzicht

Weergave touchscreen

Opstartanimatie

Bezig met initialiseren.

Constant wit

Fabrieksinstellingen, wachten op acceptatie.

Constant blauw

Succesvol opgenomen in een netwerk en correct werkend.

Locatie-animatie

Dit geeft aan dat u in de UniFi Controller-software op Locate (Zoeken) hebt geklikt. De software geeft ook de locatie van het apparaat weer op de kaart.

RJ45 snelheid/verbinding/activiteit-lampje (poort 1 - 24)

Uit

Geen verbinding

Oranje

Verbinding vastgesteld op 10/100 Mbps

Een knipperend lampje geeft aan dat er activiteit is

Groen

Verbinding vastgesteld op 1000 Mbps

Een knipperend lampje geeft aan dat er activiteit is

SFP verbinding/activiteit-lampje (poort 25 - 26)

Uit

Geen verbinding

Groen

Verbinding vastgesteld op 1 Gbps

Een knipperend lampje geeft aan dat er activiteit is

RJ45 (poort 1 - 24)

RJ45-poorten ondersteunen Ethernet-verbindingen van 10/100/1000 Mbps.

SFP (poort 25 - 26)

Hot swappable SFP-poorten ondersteunen verbindingen van 1 Gbps.

Reset-knop

Deze knop heeft twee functies voor de UniFi Switch:

  • Opnieuw opstarten Druk kort op de Reset-knop en laat weer los.
  • Herstellen naar fabrieksinstellingen Houd de Reset-knop langer dan vijf seconden ingedrukt.

Voedingspoort

Sluit het meegeleverde netsnoer aan op de voedingspoort.

Installatievereisten

Hardware-installatie

  1. OF

Stroom aansluiten

Ethernet aansluiten

SFP aansluiten

Voor informatie over compatibele glasvezel SFP-modules gaat u naar: ubnt.link/UniFi_SFP_DAC_Compatibility

Specificaties

USW-24

Afmetingen

442,4 x 200 x 43,7 mm
(17,42 x 7,87 x 1,72")

Gewicht

2,70 kg (5,95 lb)

Met beugels voor rekmontage2,79 kg (6,15 lb)

Interfaces

Verbinden via netwerk(24) 10/100/1000 RJ45-poorten
(2) 1G SFP Ethernet-poorten
BeheerEthernet In-Band

Voedingsbron

100-240 VAC, 50/60 Hz, universele ingangsspanning

Voeding

AC/DC, intern, 36W

Ondersteund spanningsbereik

100 tot 240 VAC

Max. stroomverbruik

25W

Lampjes

RJ45-datapoortSnelheid/verbinding/activiteit
SFP-datapoortenVerbinding/activiteit

ESD/EMP-bescherming

Lucht: ± 16 kV, Contact: ± 12 kV

Schokken en trillingen

ETSI300-019-1.4 Standaard

Bedrijfstemperatuur

-5 tot 45° C (23 tot 113° F)

Bedrijfsvochtigheid

10 tot 90% niet-condenserend

Certificeringen

CE, FCC, IC

Safety Notices

  1. Read, follow, and keep these instructions.
  2. Heed all warnings.
  3. Only use attachments/accessories specified by the manufacturer.

Warning

WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow.

Warning

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

Warning

WARNING: Do not use this product in location that can be submerged by water.

Warning

WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Electrical Safety Information

  1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
  2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
  3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
    1. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
    2. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.
    3. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
    4. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
    5. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

ISED Canada

CAN ICES-3(A)/NMB-3(A)

Australia and New Zealand

RCM

Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

CE Marking

CE marking on this product represents the product is in compliance with all directives that are applicable to it.

CE

WEEE Compliance Statement

Conformiteitsverklaring

Online Resources

SupportCommunityDownloads