×

Click for
Table of Contents

menuUAP-nanoHD Quick Start Guide

Package Contents

UniFi nanoHD AP
Mounting Bracket
Ceiling Backing Plate
Screws (Qty. 4)
Flat Head Screws (Qty. 4)
Keps Nuts (Qty. 4)
Screw Anchors (Qty. 4)
Gigabit PoE* (48V, 0.3A) with Mount Bracket
Power Cord*

* Included only in the single-pack of the UAP-nanoHD.

Installation Requirements

IMPORTANT: The UAP-nanoHD requires the UniFi Controller v5.7 or higher, available at: ui.com/download/unifi

System Requirements

Hardware Overview

LED

Ports

Locking Notch

The Locking Notch will be used with the Mounting Bracket to help secure the UniFi AP. (This is described further in the Mounting Bracket section.)

Reset

The Reset button serves two functions for the UniFi AP:

  • Restart Press and release the Reset button quickly.
  • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

Ethernet

This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.

Cable Feed Plug

If your Ethernet cable feeds along the mounting surface, remove the Cable Feed Plug.

Mounting Bracket

Locking Tab

During installation, the Locking Tab on the Mounting Bracket moves from the Initial Position to the Final Position, where the Locking Tab fits securely into the Locking Notch on the UniFi AP to help prevent theft.

Initial Position

Final Position

Note: If you need to remove the UniFi AP from the Mounting Bracket, insert a paper clip in the Slot to release the Locking Tab and turn the UniFi AP counterclockwise.

Hardware Installation

The device can be mounted on the wall or ceiling. Perform the steps for the appropriate installation.

Wall Mount

  1. Optional

  2. Optional

Ceiling Mount

Powering the UniFi AP

The UAP-nanoHD features auto-sensing 802.3af PoE support and can be powered by any of the following:

The single-pack of the UAP-nanoHD includes one Gigabit PoE adapter. For multi-pack units, PoE adapters or a UniFi Switch with PoE may be purchased separately.

Connecting to a PoE Switch

Connect the Ethernet cable from the UniFi AP directly to an 802.3af-compliant port on the switch.

Specifications

UAP-nanoHD

Dimensions

160 x 160 x 32.65 mm

(6.3 x 6.3 x 1.29")

Weight

  • With Mounting Kits

300 g (10.6 oz)

  • 315 g (11.1 oz)

Networking Interface

(1) RJ45 GbE

Buttons

(1) Reset to Defaults

Power Method

802.3af

Power Supply

48V, 0.3A Gigabit PoE Adapter*

Max. Power Consumption

10.5W

Operating Frequency

2.4 GHz

5 GHz

Max. TX Power

  • 2.4 GHz
  • 5 GHz
  • 23 dBm
  • 26 dBm

Antenna Gain

  • 2.4 GHz
  • 5 GHz
  • 2.8 dBi
  • 3 dBi

MIMO

  • 2.4 GHz
  • 5 GHz
  • 2x2
  • 4x4

Radio Rate

  • 2.4 GHz
  • 5 GHz
  • 300 Mbps
  • 1733 Mbps

Wi-Fi Standards

802.11 a/b/g/n/ac/ac-wave2

Wireless Security

WEP, WPA-PSK,
WPA-Enterprise (WPA/WPA2, TKIP/AES)

BSSID

8 per Radio

Mounting

Wall/Ceiling (Kits Included)

Operating Temperature

-10 to 70° C (14 to 158° F)

Operating Humidity

5 to 95% Noncondensing

Certifications

CE, FCC, IC

* Only the single-pack of the UAP-nanoHD includes a PoE adapter.

Operating Frequency (MHz)

US/CA

2400 - 2483.5

U-NII-1

5150 - 5250

U-NII-2A

5250 - 5350

U-NII-2C

5470 - 5725

U-NII-3

5725 - 5850

Worldwide

2400 - 2483.5
5150 - 5875