Package Contents

Installation Requirements

• The PS-5AC can be used with one of the following antennas (not included):
  • Horn-5-30
  • Horn-5-45
  • Horn-5-60
  • Horn-5-90
  • U-OMT-Dish
• The GPS Antenna needs to have clear line of sight to the sky for proper GPS operation.
• 13 mm wrench
• 5 mm hex socket (recommended for the Mounting Bracket)
• Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable

• Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the PrismStation and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.

* Shown with the Horn-5-45

Hardware Overview

Power LED
The LED will light blue when the device is connected to a power source.
Reset Button
To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is already powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.
GPS Antenna Connector
This is used to connect the included GPS Antenna.
Ethernet Port
This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.
Release Button
To remove the attached horn antenna, rotate the horn antenna counterclockwise while depressing the Release Button.

Hardware Installation

These instructions show the Horn-5-45; however, the PrismStation is also compatible with the following antennas:

• Horn-5-30
• Horn-5-60
• Horn-5-90
• U-OMT-Dish (refer to the U-OMT-Dish Quick Start Guide for installation instructions)

1. 

2. 

Pole-Mounting

1. 

2. 

3. 

4. 

5. 

6. 

7. 

8. 

9. 

Connecting Ethernet and GPS

1. 

2. 

3. 

4. 

5. 

6. 

7. 

8. 

9. 

Connecting Power

	WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide.

OR

Accessing airOS via Wi-Fi

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.

The Antenna and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.

Specifications

PS-5AC
Dimensions   Mounting Hardware Only	155 x 155 x 104 mm (5.16 x 5.16 x 4.09") 83 x 117 x 69 mm (3.27 x 4.61 x 2.72")
Weight Mounting Hardware Only	0.77 kg (1.70 lb) 0.79 kg (1.74 lb)
Networking Interface	(1) 10/100/1000 Ethernet Port
RF Connector	(1) GPS
LED	Power
Max. Power Consumption	10W
Power Supply	24V, 1A Gigabit PoE Adapter (Included)
Power Method	24V Passive PoE (Pairs 4, 5+; 7, 8 Return)
Supported Voltage Range	20 to 26VDC
Wind Loading	31 N @ 200 km/h (7 lbf @ 125 mph)
Wind Survivability	200 km/h (125 mph)
Operating Temperature	-40 to 70° C (-40 to 158° F)
Operating Humidity	5 to 95% Noncondensing
Mounting	Pole-Mount (Kit Included)
ESD/EMP Protection	± 24kV Contact/Air
Certifications	CE, FCC, IC

Operating Frequency (MHz)
US/CA	U-NII-1	5150 - 5250
	U-NII-2A	5250 - 5350
	U-NII-2C	5470 - 5725
	U-NII-3	5725 - 5850
Worldwide	5150 - 5875

Management Radio (MHz)
US/CA	2412 - 2462
Worldwide	2412 - 2472