×

Click for
Table of Contents

menuPBE-M5-400 Quick Start Guide

Package Contents

Reflector
Antenna Feed*
Rear Housing
Mounting Bracket
Pole Clamp
U-Bolt
Flange Nuts (Qty. 2)
Gigabit PoE (24V, 0.5A) with Mounting Bracket
Power Cord

* The PBE-M5-400 Antenna Feed has a thin gray ring around the center of the cap to differentiate it from the PBE-M5-300 Antenna Feed.

Installation Requirements

We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable

Hardware Overview

Ethernet

This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.

Reset Button

To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.

Release Button

After you assemble the device, check the Release button; it should be fully engaged in the Release Button Slot of the Rear Housing. This ensures that the Antenna Feed is locked into place. If you need to remove the Antenna Feed, you must depress the Release button first.

Signal LEDs

In airOS®, you can modify the threshold values for the wireless signal strength LEDs on the Advanced tab under Signal LED Thresholds. The default values are shown below:

Ethernet LED

The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity.

Power LED

The Power LED will light green when the device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Reflector installed provides directional outdoor coverage (gain is reflector-dependent).

The PowerBeam mounted outdoors without the Reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only.

Installation

Optional (radome not included)

Connecting Power

WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide.

OR

Optional

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

  1. Make sure that your host system is connected via Ethernet to the device.
  2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
  3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac).

  4. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.

The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For details, refer to the User Guide available at ui.com/download/airmax

You can also manage your device using the Ubiquiti Internet Service Provider Application. Setup using the UISP app requires the U-Installer, sold separately.

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.

Antenna

Select your antenna from the list. If Calculate EIRP Limit is enabled, transmit output power is automatically adjusted to comply with the regulations of the applicable country. Note the requirements and antenna types listed below.

Cable Loss (When applicable)

Enter the cable loss in dB. Output power is adjusted to compensate for loss between the radio and the antenna.

Certified Antenna Types

This radio transmitter FCC ID: SWX-PBE5M / IC: 6545A-PBE5M has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. Antenna types not included in this list or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna

Frequency

Gain

Dish

5 GHz

25 dBi

Specifications

PBE-M5-400

Dimensions

420 x 420 x 275 mm

(16.54 x 16.54 x 10.83")

Weight (Mount Included)

1.753 kg

(4.789 lb)

Gain

25 dBi

Networking Interface

(1) 10/100/1000 Ethernet Port

Enclosure

Outdoor UV Stabilized Plastic

Max. Power Consumption

8W

Max. TX Power

26 dBm

Power Supply

24V, 0.5A Gigabit PoE Adapter (Included)

Power Method

Passive PoE (Pairs 4, 5+; 7, 8 Return)

Wind Survivability

200 km/h

(125 mph)

Wind Loading

342.5 N @ 200 km/h

(77 lbf @ 125 mph)

Mounting

Pole Mounting Kit Included

Salt Fog Test

IEC 68-2-11 (ASTM B117),
Equivalent: MIL-STD-810 G Method 509.5

Vibration Test

IEC 68-2-6

Temperature Shock Test

IEC 68-2-14

UV Test

IEC 68-2-5 at 40° C (104° F)
Equivalent: ETS 300 019-1-4

Wind-Driven Rain Test

ETS 300 019-1-4
Equivalent: MIL-STD-810 G Method 506.5

Operating Temperature

-40 to 70° C (-40 to 158° F)

Operating Humidity

5 to 95% Noncondensing

Certifications

CE, FCC, IC

Operating Frequency (MHz)

Worldwide

5150 - 5875

US/CA

U-NII-1

5150 - 5250

U-NII-2A

5250 - 5350

U-NII-2C

5470 - 5725

U-NII-3

5725 - 5850