Package Contents

Installation Requirements

• Pole-mounting: 7 mm socket wrench or screwdriver
• Wall-mounting: wall fastener (not included)
• Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable

• Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoBeam and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.

Hardware Overview

Reset Button
To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.
Ethernet Port
This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.
Power LED
The Power LED will light blue when the device is connected to a power source.
Ethernet LED
The Ethernet LED will light steady blue when an active Ethernet connection is made and flash when there is activity.
Signal LEDs
In airOS®, you can modify the threshold value for the wireless signal strength LEDs on the Wireless tab under Signal LED Thresholds. Each LED will light when the wireless signal strength is equal to or greater than the LED’s threshold value. The default threshold values for these LEDs are shown below:

Hardware Installation

Go to the appropriate mounting instructions: Pole Mounting or “Wall Mounting”.

	Note: The NanoBeam can also be mounted inside a window using the NanoBeam Window Mount, model NBE-19-WM (sold separately). For instructions, see the NanoBeam Window Mount Quick Start Guide.

Pole Mounting

1. 

2. 

3. 

4. 

Wall Mounting

The NanoBeam must be mounted directly to a wood stud or other structurally stable surface to avoid damage to the mounting hole when you adjust the aim.

Optional Accessory

To enhance stability, you can use the NanoBeam Wall Mount Kit, model NBE-WMK (sold separately).

	Note: Center screw included. Two optional screws (not included) provide additional stability.

Installation Instructions

1. 

2. 

3.  

Fastener (not included)

OR

NanoBeam Wall Mount Kit

4. 

Aiming

1. 

2. 

Connecting Power

1. 

2. 

3. 

4. Connect the power using:

• included Gigabit PoE Adapter
• PoE switch

	WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide.

Accessing airOS via Wi-Fi

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.

The Output Power field is provided to the professional installer to assist in meeting regulatory requirements.

Specifications

NBE-2AC-13
Dimensions (Mount Included)	189 x 189 x 125 mm (7.44 x 7.44 x 4.92")
Weight (Mount Included)	530 g (1.17 lb)
Gain	13 dBi
Networking Interface	(1) 10/100/1000 Ethernet Port
Enclosure	Outdoor UV Stabilized Plastic
Max. Power Consumption	7.5W
Power Supply	24V, 0.5A Gigabit PoE Adapter (Included)
Power Method	Passive PoE (Pairs 4, 5+; 7, 8 Return)
Wind Loading	45.4 N @ 200 km/h (10.2 lbf @ 125 mph)
Wind Survivability	200 km/h (125 mph)
Mounting	Pole-Mount (Kit Included) Wall-Mount (Not Included) Window-Mount (Not Included)
ESD/EMP Protection	± 24kV Contact/Air
Operating Temperature	-40 to 70° C (-40 to 158° F)
Operating Humidity	5 to 95% Noncondensing
Certifications	CE, FCC, IC

Operating Frequency (MHz)
Worldwide	2412 - 2472
US/CA	2412 - 2462

Management Radio (MHz)
Worldwide	5150 - 5250
US/CA	U-NII-3: 5725 - 5850