Package Contents

* Included only in the single-pack of the ES-10XP

Installation Requirements

• Wall-mounting (optional)
  • Drill with 6 mm drill bit
  • Phillips screwdriver
• For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable

	Note: Although the cabling can be located outdoors, the EdgeSwitch itself should be housed inside a protective enclosure.

Hardware Overview

System LED
Flashing White	Bootup in Progress
White	Ready for Use Not Connected to Ubiquiti Internet Service Provider (UISP™)
Blue	Ready for Use Connected to UISP
Steady Blue with Occasional Flashing	Ready for Use Unable to Connect to UISP
Quickly Flashing Blue	Used to Locate a Device in UISP
Alternating Blue/White	Firmware Upgrade in Progress
RJ45 PoE LED (Ports 1 - 8)
Off	No Power over Ethernet
Green	24V Power over Ethernet
RJ45 Speed/Link/Activity LED (Ports 1 - 8)
Off	No Link
Amber	Link Established at 10/100 Mbps Flashing Indicates Activity
Green	Link Established at 1000 Mbps Flashing Indicates Activity
SFP Link/Activity LED (Ports 9 - 10)
Off	No Link
Green	Link Established at 1 Gbps Flashing Indicates Activity
RJ45 (Ports 1 - 8)
RJ45 ports support 10/100/1000 Ethernet connections and 24V Passive Power over Ethernet (PoE) output.
SFP (Ports 9 - 10)
Hot-swappable SFP ports support 1 Gbps connections. If you use a copper Ethernet module (example: UF-RJ45-1G), power off the EdgeSwitch before insertion; otherwise there may be a device reboot.
Reset Button
To reset to factory defaults: Disconnect power from the EdgeSwitch. Reconnect power while holding the Reset button. The port LEDs will light up in sequential order (this takes approximately five seconds). When the port 1 LED flashes again, release the Reset button.
Power
Connect the included Power Adapter to the Power port.
Grounding Point
Ground bonding point for an optional ground wire.

Hardware Installation

The optional EdgeRouter™ Rackmount Kit, model ER-RMKIT, is sold separately.

	WARNING: The EdgeSwitch ES-10XP must not be stacked. Do not place it on top of another switch. Do not place anything on top of the ES-10XP.

Wall Mounting

1. 

2. 

3. 

4. 

Grounding the EdgeSwitch (Recommended)

The Power Adapter grounds the device; however, you can add optional ESD grounding for enhanced ESD protection (ground wire not included).

Connecting Power

1. 

2. 

Connecting Ethernet

Using SFP Ports

1. 

2. 

3. 

For information about compatible fiber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility

Accessing the Configuration Interface

The EdgeSwitch is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.20. Proceed to the appropriate section, DHCP or “Fallback IP Address”:

DHCP

Use one of the following methods:

• Set up the DHCP server to provide a specific IP address to the EdgeSwitch based on its MAC address (on the label).
• Let the EdgeSwitch obtain an IP address and then check the DHCP server to see which IP address was assigned.

To log in, follow these steps:

1. Launch your web browser. Type the appropriate IP address in the address field. Press enter (PC) or return (Mac).
2. Enter ubnt in the Username and Password fields. Click Sign In.

The EdgeSwitch Configuration Interface will appear. Customize additional settings as needed. For 24V Passive PoE configuration, refer to “Configuring PoE Settings”. For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax

Fallback IP Address

1. Ensure that your computer (or other host system) is connected to the EdgeSwitch.
2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type the appropriate IP address in the address field (192.168.1.20 is the default fallback IP address). Press enter (PC) or return (Mac).

   

4. Enter ubnt in the Username and Password fields. Click Sign In.
5. The EdgeSwitch Configuration Interface will appear. Click the System Settings tab.
6. Change the IP Address to a unique IP address. Click Apply.

	Note: If you change the IP settings, the session will be cut off, and you will need to reconnect to the EdgeSwitch using the new IP address.

Customize additional settings as needed. For 24V Passive PoE configuration, refer to “Configuring PoE Settings”. For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax

Configuring PoE Settings

The PoE setting for ports 1-8 is set to Off by default.

	WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage.

On the Dashboard tab, click the PoE setting of the Ethernet port you want to configure. Then select 24V.

UISP Management

You can manage your device using UISP, which lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at uisp.ui.com

Specifications

ES-10XP
Dimensions	207 x 31.1 x 90 mm (8.15 x 1.22 x 3.54")
Weight	500 g (1.10 lb)
Total Non-Blocking Throughput	10 Gbps
Switching Capacity	20 Gbps
Forwarding Rate	14.88 Mpps
Max. Power Consumption (Excluding PoE Output)	8W
Power Method	24VDC, 2.5A
Supported Voltage Range	9 - 30VDC, 5A
Power Supply	24VDC, 2.5A Power Adapter (Included)
LEDs
System	Status
RJ45 Data Ports	PoE, Link/Speed/Activity
SFP Data Ports	Link/Activity
Networking Interfaces	(8) 10/100/1000 Mbps RJ45 Ports (2) 1 Gbps SFP Ports
Management Interface	Ethernet In-Band
Certifications	CE, FCC, IC
ESD/EMP Protection	Air: ± 24 kV, Contact: ± 24 kV
Operating Temperature	-10 to 50° C (14 to 122° F)
Operating Humidity	5 to 95% Noncondensing
Shock and Vibration	ETSI300-019-1.4 Standard

PoE
PoE Interface	(8) 24VDC Passive PoE (Pins 4, 5+; 7, 8-)
Max. Passive PoE Wattage per Port	15W
24V Passive PoE Voltage Range	24V