×

Click for
Table of Contents

menúBulletM2-HP Quick Start Guide

Package Contents

Bullet M2
Compression Seal

Installation Requirements

* Shown without antenna.

Hardware Overview

Signal LEDs

In airOS®, you can modify the threshold values for the wireless signal strength LEDs on the Advanced tab under Signal LED Thresholds. The default values are shown below:

Ethernet LED

The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity.

Power LED

The Power LED will light green when the device is connected to a power source.

Reset Button

To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on.

Ethernet Port

This 10/100 Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.

Hardware Installation

Accessing airOS

Verify connectivity in the airOS® Configuration Interface.

  1. Make sure that your host machine is connected via Ethernet to the device.
  2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
  3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac).

  4. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.

The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For additional details on the airOS Configuration Interface, refer to the User Guide available at: ui.com/download/airmax

You can also manage your device using the Ubiquiti Network Management System. Setup using the UNMS app requires the U-Installer, sold separately.

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.

Antena

Select your antenna from the list. Ensure Calculate EIRP Limit is enabled; transmit output power is automatically adjusted to comply with the regulations of the applicable country. For a Custom antenna, Antenna Gain is entered manually. Note the requirements and antenna types listed below.

Cable Loss (When applicable)

Enter the cable loss in dB. Output power is adjusted to compensate for loss between the radio and the antenna.

Certified Antenna Types

This radio transmitter FCC ID: FCC: SWX-M2BW / IC: 6545A-M2BW has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. Antenna types not included in this list or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna

Frequency

Gain

Omni

2.4 GHz

13 dBi

Sector

2.4 GHz

17 dBi

Dish

2.4 GHz

24 dBi

Specifications

BulletM2-HP

Dimensions

163.65 x 38.75 x 38.75 mm
(7.48 x 1.53 x 1.53
")

Weight

130 g (4.59 oz)

Enclosure

Polycarbonate

Networking Interface

10/100 Mbps

Antenna Connector

N-Type Connector

LEDs

Power, Ethernet,
(4) Signal Strength

Max. Power Consumption

7W

Output Power

25 dBm

Power Supply

AC to 24VDC, 0.5A Gigabit PoE Adapter

Power Method

24V Passive PoE
(Pairs 4, 5+; 7, 8-)

ESD/EMP Protection

± 24 kV Contact/Air

Operating Temperature

-40 to 70° C (-40 to 158° F)

Operating Humidity

5 to 95% Condensing

Shock and Vibration

ETSI300-019-1.4

Certifications

CE, FCC, IC

Operating Frequency (MHz)

US/CA

2412 - 2462

Worldwide

2412 - 2472