Package Contents
 |
|---|
| Dish Reflector |
 |
|---|
| Antenna Feed |
 |
|---|
| Protective Shroud |
 |
|---|
| Mount Bracket |
 |
|---|
| Pole Clamps (Qty. 2) |
 |
|---|
| Stabilizer Brackets (Qty. 2) |
 |
|---|
| RF Cables (Qty. 2) |
 |
|---|
| Elevation Rod Assembly |
 |
|---|
| M10x150 Carriage Bolts (Qty. 4) |
 |
|---|
| M10x100 Bolts (Qty. 2) |
 |
|---|
| M10x25 Carriage Bolts (Qty. 3) |
 |
|---|
| M4 Screws (Qty. 4) |
Installation Requirements
- airFiber 3X radio (sold separately)
- Phillips screwdriver
- 16 mm wrench
- 24 mm wrench
- Clear view of the sky for proper GPS operation
- Mounting point:
- At least 1 m below the highest point on the structure
- For tower installations, at least 3 m below the top of the tower
- Ground wire – min. 10 AWG (5 mm2) and max. length: 1 m. As a safety precaution, ground the airFiber radio to a grounded mast, pole, tower, or grounding bar.
- Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.
| WARNING: Failure to properly ground your airFiber radio will void your warranty. |
|---|
Hardware Installation
|
|
Important: Handle the Dish Reflector with care. Deformations in its shape may reduce the antenna’s effectiveness. |
|---|
| Important: Do not handle the antenna by the Antenna Feed once the feed is connected. |
|---|
At the installation site, secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar.
| WARNING: Failure to properly ground your airFiber radio will void your warranty. |
|---|
| Note: The ground wire should be as short as possible and no longer than one meter in length. |
|---|
| Note: The magnetic GPS antenna is included with the airFiber radio. Place it on the Dish Reflector (this is temporary; you will place the GPS antenna on the GPS antenna mount later). |
|---|
Mounting the GPS Antenna
Locate a mounting point that has a clear view to the sky, and is above and as far away as possible from the antenna.
|
|
Note: All GPS items are included with the airFiber radio. |
|---|
OR
Specifications
|
AF-3G26-S45 |
|
|
Dimensions |
650 x 650 x 300 mm (25.6 x 25.6 x 11.8") |
|---|---|
|
Weight |
9.8 kg (21.61 lb) |
|
Frequency |
3.3 - 3.8 GHz |
|
Gain |
26 dBi |
|
HPOL Beamwidth |
7° (6 dB) |
|
VPOL Beamwidth |
7° (6 dB) |
|
Front-to-Back Ratio |
-33 dB |
|
Max. VSWR |
1.4:1 |
|
Wind Survivability |
200 km/h (125 mph) |
|
Wind Loading |
787 N @ 200 km/h (177 lbf @ 125 mph) |
|
Polarization |
Dual Linear |
|
Cross-Pol Isolation |
35 dB Min. |
|
ETSI Specification |
EN 302 326 DN2 |
|
Mounting |
Universal Pole Mount, airFiber Radio Mount, and Weatherproof RF Jumpers Included |