airOS8 Firmware Changelog ==== Supported products * Rocket 5AC Lite, model: R5AC-Lite * Rocket 5AC PTP AirPrism, model: R5AC-PTP * Rocket 5AC Multi-Point AirPrism, model: R5AC-PTMP * PowerBeam 5AC, models: PBE-5AC-500, PBE-5AC-620, PBE-5AC-300, PBE-5AC-400 * PowerBeam 5AC 300 ISO, model: PBE-5AC-300-ISO * PowerBeam 5AC 400 ISO, model: PBE-5AC-400-ISO * PowerBeam 5AC 500 ISO, model: PBE-5AC-500-ISO * NanoBeam 5AC 19dBi, model: NBE-5AC-19 * NanoBeam 5AC 16dBi, model: NBE-5AC-16 * LiteBeam 5AC 23dBi, model: LBE-5AC-23 * LiteBeam AC 16 dBi 120 degrees, model: LBE-AC-16-120 * Rocket 5AC Prism, model: R5-AC-PRISM * PrismStation 5AC, model: PS-5AC * IsoStation 5AC, model: IS-5AC * NanoStation 5AC loco, model: NS-5ACL * NanoBeam 5AC GEN2, model: NBE-5AC-GEN2 * LiteBeam 5AC GEN2, model: LBE-5AC-GEN2 * PowerBeam 5AC GEN2, model: PBE-5AC-GEN2 * Rocket Prism 5AC GEN2, model: RP-5AC-GEN2 ==== 8.4.2 (XC, WA) Changelog / October 17, 2017 ==== - Fix: Security patch for the WPA2 vulnerability called KRACK 8.4.1 (XC, WA) Changelog / October 6, 2017 ==== - New: Default TDD Fixed Frame mode Capacity reporting format changed to same format as Flexible Frame mode. New option added to System page to change the preferred reporting method. - Fix: High memory usage when UNMS is enabled - WEB UI: airMagic doesn't show full frequency range for FCC SKUs 8.4.0 (XC, WA) Changelog / September 29, 2017 ==== Important: - Maximum supported CPE/Station count limited to 60 while in GPS Sync mode New: - New: TDD Framing/GPS Sync support for 20/40MHz in AP PtMP airMAX Mixed mode (XW, v6.1.0 required) - New: Enable/disable AMSDU aggregation in Wireless Advanced section - New: VRRP IPv6 passthrough - New: Antenna selection list for PrismStation 5AC and IsoStation 5AC - New: Upgrade miniupnpd to v2.0 Improvements: - Improved long range PTP mode - Improved scan for non-DFS frequencies (active scan) - Improvements to VoIP performance - AirOS stability improvements - AirOS security improvements Fixes: - Fix: VRRP passthrough - Fix: ATPC issue on SISO devices - Fix: Latency spikes when Station disconnects - Fix: RX Capacity drop on Station in PTMP mode after scan - Fix: Site Survey doesn't show all available APs after scan - Fix: airMagic is not working in some cases when devices are misconfigured - Fix: Station doesn't connect back to AP with the strongest RSSI in case of several APs with the same SSID - Fix: Sometimes home routers fail to renew DHCP lease (fixed regression in dnsmasq v2.66) - Fix: Reduced HW Watchdog resets (possible fix) WEB UI: - WEB UI: Device model reporting on Dashboard header - WEB UI: Show warning in airMagic if airView is disabled - WEB UI: Show warning in Speed Test if Destination IP is the same as device IP in Speed Test - WEB UI: Show ambient noise and corresponding frequency on mouse hover in Dashboard on airView bar - WEB UI: Improve Rate and Burst values parsing and validation in Traffic Shaper Rule - WEB UI: LAN Speed, Cable SNR & Length reporting for 2nd Ethernet port for local & remote devices on Dashboard - WEB UI: Disable Signal, Noise & Interference charts if remote station doesn't provide required data - WEB UI: Hide airView enable/disable option if device doesn't have airView radio - WEB UI: Don't allow extensions (i.e., LastPass) to fill in configuration fields - WEB UI: Impossible to Clear or Refresh System log on mobile phones - WEB UI: airMagic doesn't show full frequency range - WEB UI: Reconnect button visibility issue 8.3.2 (XC, WA) Changelog / September 1, 2017 ==== New: - New: Add support for RFC 6598 (CGN) private IP responses via Discovery - New: Google Play and Apple Store icons on login page - New: Add option to disable airView radio - airMAX-ac FF: Fixed Frame mode improved performance for AP with one client (for PTP) Fixes: - Fix: ATPC issue on SISO devices - Fix: DHCP Options saved in system.cfg are lost when applying Web UI changes - Fix: Applying Wireless settings changes first time after upgrade causes full restart - Fix: Client Isolation is not working on VLAN bridges (bridge index greater than 0) - Fix: There should be no SOHO Router network mode for any airMAX AC product - Fix: Management Radio operation for New Zealand WEB UI: - WEB UI: DHCP Server Range does not match LAN IP address when enabling DHCP Server - WEB UI: After HTTP port change to 8080 WEB UI can't be accessed while Management Radio is enabled (not in airView mode) - WEB UI: Slightly relaxed password requirements - WEB UI: AP selection window is broken on mobile phones - WEB UI: Update Chinese translation 8.3.1 (XC, WA) Changelog / July 28, 2017 ==== - airMAX-ac FF: Fix AP issue in FF mode - airMAX-ac FF: Improve association time - airMAX-ac FF: Improve uplink performance - airMAX-ac FF: 8ms 75/25 40 MHz duplex speedtest causes rates fluctuation after uplink optimization Fixes: - Fix: Scan all channel widths fails on AP in TDD Fixed frame mode - Fix: DNS proxy is not working when Block Management Access is enabled on LAN - Fix: Improved Stations authentication time. Reduced disconnects on security keys exchange - Fix: Applying Wireless settings changes first time after upgrade causes full restart - Fix: Access Point ignores Session-Timeout limit received from RADIUS server - Fix: 5830MHz is missing from Center Frequency when using 20MHz channel width - Fix: TX reporting issues in Speed Test tool - Fix: Management VLAN traffic issues - Fix: Reduced HW Watchdog resets (possible fix) WEB UI: - WEB UI: Make TDD Framing section always visible - WEB UI: False indication of signal difference per chain on Dashboard for SISO devices - WEB UI: Incorrect PtMP distance warning when exceeding ACK limits in PtP mode - WEB UI: Removed minimum BURST value validation in Traffic Shaper Rule - WEB UI: Device name does not handle special characters correctly - WEB UI: Can't close Tools and Log dialogs when page is scrolled down before opening the dialog or when using small screens - WEB UI: Default Firewall Mask 0.0.0.0/0 does not show up if it was entered manually in Firewall Rules - WEB UI: Manage airGateway button is not fully visible in Device details 8.3.0 (XC, WA) Changelog / June 16, 2017 ==== New: - New: GPS Sync support for airMAX AC - New: Secondary SSID support on Station mode - New: Auto-channel width selection on Station if the AP's channel width is changed - New: UNMS (Ubiquiti Networks Management System) support - New: Kick All in Station List for reconnecting all stations from AP - New: Add Speed Test quick launch button to station list - New: Remember Credentials For This Session setting for saving User Name and Password in Speed Test tool - New: Enhanced password change validation for security purposes Fixes: - Fix: Sometimes Site Survey shows no results on Station (PTP mode) WEB UI: - WEB UI: Show UNMS status and last connection time for Local Device on Dashboard - WEB UI: Show the tooltip for truncated long device name on Dashboard - WEB UI: Indication of combined signal on Dashboard when signal difference per chain exceeds recommended maximum of 5 dBm - WEB UI: Show values in Capacity/Throughput and Signal, Noise & Interference chart legends - WEB UI: Open Tools menu in front of all other windows - WEB UI: Invalid parameters error in Speed Test when specifying IP manually - WEB UI: Dashboard graphs are redrawn when a new Station is connected - WEB UI: Fixed Distance reporting on Dashboard - WEB UI: airView scrollbar issue 8.1.4 (XC, WA) Changelog / June 8, 2017 ==== - Fix: Regression in networks operation. In some cases it causes network loops, switch port flapping, and doubled multicast/broadcast packets (affects only v8.1.3) - Fix: DHCP Address Reservation issue 8.1.3 (XC, WA) Changelog / June 2, 2017 ==== - New: Add option to enable/disable ATPC on Station - New: Show GPS coordinates (with the link to Google Maps) in Dashboard - New: Added NTP Client information and tooltip next to Date on Dashboard - New: Keyboard shortcuts: s - brings up the Station List on Dashboard, c - opens/closes the Constellation Diagrams window in all pages - New: Help files for Management Radio Settings - airMAX AC improvements - airOS stability improvements - airOS security improvements - Improved Dashboard usability - Improved Current and Expected rates representation in Rate diagram in Dashboard - Improved password change validation - Use TCP protocol instead of UDP for UBNT discovery queries from Public IPs Regulatory updates: - Added HT40 and HT80 channel widths for Saudi Arabia - Fix: Sometimes Stations do not reconnect to AP after mass kick out (PTMP mode) - Fix: AP is rebooting after when 88th Station tries to connect - Fix: DHCP discovery is blocked when Block Management Access is enabled on LAN - Fix: Device becomes unreachable until reboot when switching form Router to Bridge mode and Block Management Access on LAN (BRIDGE0) was enabled - Fix: AP drops Stations when Site Survey is scanning on AP/Station in airMAX AC Mixed mode - Fix: Sometimes Site Survey shows no results on Station (PTP mode) - Fix: Device becomes unreachable when running Speed Test on Ethernet links - Fix: Speed Test results average values calculation - Fix: Connection interruption on interfaces running DHCPC when wpa_supplicant is configured - Fix: Show DHCP client hostname in DHCP Leases in case hostname contains special symbols - Fix: NAT helper modules are not enabled/disabled on configuration change until device reboot - Fix: After some time PPPoE client stops sending PADI packets to reinitiate PPP session after failure - Fix: AirOS 8 doesn't pass VRRP traffic - Fix: Not so strict uploaded backup configuration checking - Fix: Disabling DNS Proxy breaks DNS - Fix: Enabling Frequency Scan List existing previously used list is not taken from configuration file - Fix: Make CoS values priority on by default on bridge with VLAN ports - Fix: Traffic Shaping is reducing speeds too much - Fix: Rate distribution data is incorrect on long range PTP links - Fix: Fixed EIRP limits for Gen2 PRISM models: Rocket 5AC PRISM Gen2 and PrismStation 5AC - Fix: Wrong distance (100km) reporting after upgrade - Fix: Error 403 if session cookie doesn't match original IP - Fix: Interface language doesn't change after changing it on first login or in System page - Fix: IE11 doesn't load the Dashboard page - Fix: Do not show wireless security type in Dashboard if device is not connected - Fix: Allow to open only one window for the same tool - Fix: Missing station 'Reconnect' option - WEB UI: Use imperial units by default - WEB UI: Allow airMAX AC series configuration backup upload - WEB UI: Added restrictions to DHCP Address Reservation - WEB UI: Improved Speed Test tool view and execution - WEB UI: Change background color to white in all dialog windows to increase contrast- WEB UI: Show values in Capacity/Throughput and Signal, Noise & Interference chart legends - WEB UI: Show warning when the link reaches or exceeds the maximum PtMP distance - WEB UI: Show error message when upgrading firmware with the same version - WEB UI: Constellation tool menu item is greyed while link is not active - WEB UI: Wrong CINR reporting for M series devices in Mixed mode - WEB UI: Missing some information on Dashboard for Read-Only user - WEB UI: Wrong Distance reporting for remote device - WEB UI: Updated Management Radio Settings labels. Settings moved to separate section - WEB UI: SSID disappears in Dashboard when Station is in scanning state - WEB UI: Different firmware version format for local and remote devices - WEB UI: airView scrollbar issue - WEB UI: Various small UI improvements 8.1.2 (XC, WA) Changelog / March 6, 2017 ==== New: - New: WEB UI Dashboard - New: AC GEN2 models support - New: Wi-Fi Radio support for easy installation - New: NanoStation 5AC model name change to NanoStation 5AC loco - New: SNMP OIDs for CPU and Memory utilisation - New: Update tcpdump to v4.9.0 Fixes: - Fix: AirOS security improvements - Fix: AirOS stability improvements (PTP and PTMP modes) - Fix: ATPC fast restart added - Fix: Auto distance calculation improvement on fast changes - Fix: Restore initial TX power on AP/PTP when ATPC is turned off - Fix: Ethernet Flow Control was not working on WA series - Fix: Broadcast echo cancellation - Fix: WPA2 EAPOL key exchange - Fix: Malformed TX/RX packet - WEB UI: Constellation diagrams moved to Tools/Constellation menu - WEB UI: Display (Auto) label for STA and AP in PTP mode - WEB UI: Hide TDMA Filter in PtP mode 8.0.2 (XC, WA) Changelog / March 28, 2017 ==== New: - New: SNMP OIDs for CPU and Memory utilisation - New: Update dropbear to v2016.74 - New: OpenSSL update to v1.0.2k - New: libevent update to v2.1.8 Fixes: - Fix: PTP mode stability and performance improvements - Fix: Security fixes and improvements - Fix: ATPC fast restart added - Fix: Restore initial TX power on AP/PTP when ATPC is turned off - Fix: Revert Device Name strictness for DHCP Client (escape only hashtag '#' symbol which breaks DHCP Client operation) - Fix: Station fails re-authentication with AP when the same SSID is used for other APs - Fix: Stations start disassociating from AP (PTMP) - Fix: ATPC feature enable/disable and ATPC target signal change interrupts wireless link - Fix: Wrong distance (100km) reporting after switching from Fixed to Auto Distance in airMAX PTP mode - Fix: Flow Control fix for WA products WEB UI: - WEB UI: Don't allow to remove BRIDGE0 interface containing WLAN0 - WEB UI: "(Auto)" label missing on STA's Remote statistics in case ATPC is enabled on AP (PTP mode only) - WEB UI: Show more detailed error messages when upgrading invalid firmware - WEB UI: Improved Station List for small screens like mobile - WEB UI: Change status.cgi output type from text/html to application/json - WEB UI: Password change validation fix 8.0.1 (XC, WA) Changelog / February 3, 2017 ==== Regulatory updates: - Revised UNII Rules activation for IC/Canada - Updated Australia allowed frequencies for 5GHz - Updated New Zealand allowed frequencies for 5GHz airOS security improvements: - OpenSSL update to v1.0.2j - XSS vulnerability in DHCP client info - Use HTTPS instead of HTTP for FW Update Check - Command injection in Ping test tool - Remove unused WMM related code - XSS in WEB UI language handling Fixes: - Fix: Reduce false A12 initialization error detection - Fix: Sometimes AP drops all Stations using WPA2 EAP security (pure AC and mixed modes affected) - Fix: Station fails re-authentication with AP using WPA2 EAP security causing Station disconnect - WEB UI: Login page improvements on small screens like mobile phones - WEB UI: Fixed sorting by Firmware version in Device Discovery tool - WEB UI: Fixed reporting of firmware version in Station List - WEB UI: French translation mistake in Login page - WEB UI: Previous device's name is showed in the title after Device Name change - WEB UI: DHCP Lease Time field should be wider - WEB UI: "Rx Signal" label misses "Rx" - WEB UI: DHCP Address Reservation section misbehavior in case DHCP Server is disabled - WEB UI: Various small UI improvements 8.0 (XC, WA) Changelog / December 16, 2016 ==== New: - New: Compatibility with airMAX M stations (airOS v6.0 required) - New: airOS8 WEB UI re-design/adoption for mobile - New: airMagic: channel selection tool (available on Access Point mode only, not all AC models supports airView radio) Access Point and Stations must run airOS8 and have dedicated airView radio. It takes few minutes to gather data after upgrade/reboot. - New: Added "TDMA Filter" slider "TDMA Filter" allows the operator to specify how much the airMAX-ac scheduler should penalise poor performing clients from a scale of 0 to 9. - New: MAC ACL support - New: Automatic Power Control - New: Hour Average & Minute Peak options in AirView (for better troubleshooting) - New: Audio Indicator to Antenna Align tool - New: Possibility to enable/disable Multicast enhancement feature - New: Remote provisioning functionality with airGateway - New: Indication of too high RX signal in Station List - New: Indication of compatibility mode wlanOpmode in mca-status - New: Indication of signal difference per chain when it exceeds recommended maximum of 5 dBm - New: Enable Block management access on WAN when switching to Router mode - New: Read-Only account support - New: HTTP login success/failures logging to system log - New: Crashlog reporting to Ubiquiti Networks for better troubleshooting - New: Noise Floor reporting in Dashboard - New: iptables modules allowing DSCP marking - New: Sensitivity Threshold on Wireless page - New: DHCP Reservation on Router mode - New: Option allowing LLDP packets to pass wireless bridge - New: Help file for Wireless Mode in Wireless Settings - New: Help file for Audio Indicator in Antenna Align Tool - New: miniUPnPd version update Regulatory updates: - LiteBeam 5AC 23: Added activation of Revised UNII band - 5GHz frequency list update for Italy: removed 5725-5875 MHz frequency range - 5GHz frequency list update for Germany: removed 5735-5755 MHz range - Removed 5.8 GHz band (EN 302 502) as not allowed for Czech Republic - Removed North America and Puerto Rico from country list for WORLD version products manufactured after 01/01/2017. Previous production data products are not affected. Fixes: - Fix: Select WAN interface for Port Forward rule by default - Fix: Optimise statistics collection (reduce CPU usage) - Fix: TX/RX counter does not reset at 4GB - Fix: Generate SSL certificate start date from firmware build timestamp - Fix: Ethernet link drops when connected to specific switch models - Fix: Don't check certificate start date if device date/time is before certificate start date (EAP TTLS/PEAP) - Fix: Ethernet RX packets drop when Flow Control is enabled - Fix: Increased Max MTU value to 2024 Bytes on WA products - Fix: Do not load NAT helpers modules when NAT is disabled - Fix: VOIP Group call doesn't work with 5 VOIP clients behind STA (Router) - Fix: Memory usage optimisation - Fix: RADIUS accounting stop frame on Client disconnect - Fix: Lower MTU fragmentation fix - Fix: DHCP on Multiple LAN interfaces separate DNS not working - Fix: PPPoE blank password sending user@domain.com - Fix: Enable Flow Control on Ethernet (LAN) after reset to factory defaults only - Fix: LAN port lockup on 10 Mbps-Half/10 Mbps-Full modes (WA series) - Fix: AP does not broadcast new Device Name after change. Reboot is required - Fix: Disable Multicast Enhancement for Station mode - Fix: SSID length for SNMP increased up to 32 characters - Fix: Device Name with not allowed symbols breaks DHCP - Fix: Changed AP device name does not take effect until reboot - Fix: airOS security improvements - Fix: Stability fixes (random reboots, crashes) - WEB UI: Keep NAT helper modules disabled when enabling NAT - WEB UI: Automatically create BRIDGE interface for each new VLANs in AP-Router setup (due to the low performance when WLAN0.vlan_id isn't included in BRIDGE) - WEB UI: Added Output Interface selection in Firewall Rules - WEB UI: Check for uploaded firmware image on device 7.2.4 (XC, WA) Changelog / July 15, 2016 ==== New: - New: Activation of revised UNII band for LiteBeam 5AC 16 120 (got FCC grant) Fixes: - Fix: Revised UNII Rules activation/deactivation for products manufactured after 06/01/2016 (due to changes in the FCC rules) - Fix: Sometimes airView radio is not initialised properly 7.2.3 (XC, WA) Changelog / July 1, 2016 ==== Regulatory updates: - Improved DFS detection for UK 7.2.2 (XC, WA) Changelog / May 27, 2016 ==== New: - New: Security enhancements - New: Disable custom scripts usage - New: lighttpd update to v1.4.39 - New: Activation of revised UNII band for PowerBeam 5AC 620 Fixes: - Fix: TX power improvements for WA series products - Fix: Security updates and improvements (malware scripts check, removal and restrictions) - WEB UI: Fixed Station List sorting by TX/RX PPS and TX Rates - WEB UI: Improved page rendering on IE, Firefox, Chrome 7.2 (XC, WA) Changelog / February 11, 2016 ==== New: - New: Revised UNII Rules activation - New: Improved 30 MHz* and 60 MHz* channel widths (replace 30 MHz and 60 MHz channel widths) - New: Option to enable/disable Flow Control - New: GPS coordinates reporting for Rocket 5AC PRISM in Dashboard page - New: Save kernel crashlog and include it in Support info archive (for better troubleshooting) - New: Linux kernel upgrade to v2.6.32.68 Regulatory updates: - Update frequency list for China: 5150-5350MHz (23dBm), DFS: 5250-5350MHz + 5725-5850MHz (33dBm) Improvements: - airMAX protocol security improvements - Improved Antenna Align Tool - Improved Site Survey scan Fixes: - Fix: 5.8GHz band (EN 302 502) isn't allowed in France - Fix: airMAX AC PTMP noisy network AP->STA direction packet loss - Fix: Reduced DFS false positive events - Fix: Reduced connection time in PTMP mode - Fix: Wireless connectivity failure on channel change - Fix: Multicast packet loss in PTMP mode - Fix: Device hang during configuration change when DHCP relay is enabled on two LAN interfaces - Fix: Incorrect security type reporting on Station after configuration changes - Fix: Allow DHCP start/end range to match to provide only single IP - Fix: UBNT stations name reporting in SNMP - Fix: 1000Mbps negotiation issue when connected to CISCO 2950t switch up-link gigabit ports - Fix: Incorrect NTP functionality when changing Time Zone - Fix: Speed Test tool no results reporting - Fix: Impossible to disable DNS proxy - Fix: On first scan Site Survey doesn't scan full frequency range - Fix: SSH client can't connect to RouterOS device - Fix: Fixed incorrect placement of the "!" iptables (router mode) - Fix: Don't allow to remove WLAN0 item from BRIDGE0 (configuration restriction to avoid low performance) - Fix: Other small changes to improve airOS stability and add additional debugging information 7.1.4 (XC, WA) Changelog / September 11, 2015 ==== Important: - Upgrade is allowed from v7.1-rc (and later) airOS version. New product support: - New: Rocket 5AC Prism (XC) - New: PowerBeam 5AC 300 ISO (WA) - New: PowerBeam 5AC 400 ISO (WA) New: - New: Graphical Site Survey view - New: Forced password change in WEB UI before apply changes - New: Ethernet advertised speed selection when auto-negotiation is enabled - New: Frequency selection in 5MHz step for all countries - New: Enabled 5.8GHz band EN 302.502 (5725 MHz - 5875 MHz) for EU - New: Upgrade Kernel to 2.6.32.65 - New: AC2 support Fixes: - Fix: Disconnects on wpa2-eap re-authentication - Fix: STA Channel pickup issue in VHT80 mode - Fix: DFS does not start CAC timer on channel which has passed all DFS procedure before - Fix: Station operating in PTMP mode can't associate to AP - Fix: Output power gets decreased when setting Antenna Gain greater than MAX Output Power - Fix: 802.11n AP with same SSID as airMAX AC AP can lock up Station association - Fix: Apply Frequency List configuration with fast restart - Fix: Multicast traffic in PTMP flows with lowest rates (as broadcasts) - Fix: SNMP reports old device name after changing it - Fix: Isolated Capacity is not available via SNMP (MIB update required) - Fix: Reset button on PoE adapter does not work - Fix: Occasional device hangs up during configuration changes - Fix: Traffic shaper doesn't filter VLAN tagged ingress traffic - Fix: Radio hangs up after output power change when doing fast restart - Fix: Port forward changes cause high CPU usage - Fix: Increase scan timeout - Fix: Throughput degradation after some time - Fix: On a PTMP AP RX airtime was incorrect - Fix: Station PTMP stops passing data (Station kick is required from AP side) - Fix: Station fails to reconnect to AP after was disconnected - Fix: Station shall send EVM report only when polled by AP - Fix: AP PTMP crash while setting TDMA parameters - Fix: PTMP download throughput is slow in large network - Fix: Unexpected Staton disconnects - Fix: Reduce bursts of remote stats. Reduce CPU usage on AP - Fix: Prevent airView radio from crashing when stations disassociate - Fix: RADIUS accounting doesn't report transferred data counters - Fix: Station can't connect after AP scan - Fix: After many channel changes radio crash - Fix: Use model for shortName in discovery packets to make it unique - Fix: Sometimes station can't connect to AP - Fix: EIRP limit calculation is wrong when Frequency List is enabled on AP - Fix: Update Pakistan regulatory. Max EIRP 20dBm(100mW) for 5GHz - Fix: Buffer overflow in PHP2 - Fix: MTU error when switching to advanced mode - Fix: Port forwarding does not work w/ PPPoE Client for WAN - Fix: Improve wait message on ambient noise graph - Fix: Main tab view issue after change STA-PTMP / AP-PTMP - Fix: DHCP server range validation issue - Fix: Remote Constellation Diagram power value is incorrect - Fix: Wrong channel width on Station main page when disconnected - Fix: Max power calculation does not take frequency list in count - Fix: Improved airOS auto update check - Fix: Added "7" to airOS logo - Fix: Show possible LAN interface negotiation speed for Auto option - Fix: Session authentication should include URL port for cookie identification - Fix: Site Survey during active scan keeps scrolling results page to the TOP - Fix: Speed Test tool returns invalid results initially 7.1.3 (XC) Changelog / July 17, 2015 ==== Important: - Upgrade is allowed from v7.1-rc (and later) airOS version. - Fix: Vulnerability via HTTP(s) allowing remote access to unauthenticated users 7.1.1 (XC) Changelog / May 19, 2015 ==== Important: - Upgrade is allowed from v7.1-rc (and later) airOS version. - New: Remove Wireless Mode (PTP/PTMP) limitations per product - Fix: Multiple priorities traffic causes high packet error rate - Fix: Frequent longer distance link disassociations on heavy traffic load - Fix: Bridge duplicates unknown unicast packets - Fix: Station sometimes doesn't reconnect to AP (PTMP operation mode) - Fix: Station can't connect to AP after it's DFS wait period end - Fix: Improved DFS false positive detection - Fix: TX/RX signals are very low just after association - Fix: Speed Test tool timeout issue - Fix: CPU load increase to 100% after high throughput load - Fix: Multicast stream can pass through one client only - Fix: AP ignores EAP Session-Timeout attribute - Fix: DHCP Client gets new IP after each release time - Fix: Faster PPPoE/DHCPC IP settings update after association when WPA2 security is used - Fix: Update EIRP limits for Brasil - Fix: Show DFS events in Syslog - Fix: WLAN TX errors counting - Fix: Include ICMP ping request (ICMP type 8) to DMZ Management port exception list - Fix: NTP client is restarting when server is unreachable - Fix: Disabling VLAN leaves associated ebtables rules enabled (may cause certain VLAN tagged traffic to not pass link) - Fix: Reduced CPU usage - Fix: Dynamic traffic shaping burst limits - Fix: Disable iptables when changing network role from Router to Bridge - Fix: IPv6 connectivity delay - Fix: Station stops passing traffic after some time - Fix: Aggregation parameters doesn't change after apply - Fix: Increase TEST mode wait time according DFS wait time period - Fix: Active channel width is not reported for STA mode after association to AP - Fix: Do full restart when configuring Frequency List - Fix: DNS servers disappear after fast restart (PPPoE/DHCP Client mode) - Fix: Disable IPv6 neighbour discovery - Fix: Wrong channel width reported in MAIN page after Station disconnect - Fix: Wireless link disconnect/lockup issue - Fix: Auto ACK/Distance miscalculation issues - Fix: Reset button on PoE adapter doesn't trigger factory reset - WEB UI: airView vertical scrollbar issue - WEB UI: add dBm labels to signal per chain values - WEB UI: Constellation diagram optimisation for IE9 - WEB UI: Sometimes "Save" button isn't active after first mouse click - WEB UI: Show disabled Antenna Gain field for products with integrated antenna - WEB UI: Distance reporting in MAIN page - WEB UI: WPA anonymous identity should be not a mandatory option - WEB UI: Password strength meter - WEB UI: Output power reporting in Device Info section - WEB UI: Add client Isolation configuration option - WEB UI: Low Speed Test result values - WEB UI: Show Firmware Version in Stations list - WEB UI: Traffic Shaper. Interface list should not include disabled interfaces - WEB UI: Doesn't load antenna gain value from configuration file - WEB UI: Hide "Client Isolation" function for AP-PTP mode - WEB UI: Switched pairs Cable pair 2 <> Cable pair 0. Added explanations on statuses OPEN, SHORT, TEST FAILED - WEB UI: Can't edit Startup Date - WEB UI: No DHCP leases in WEB UI - WEB UI: Other small changes/improvements 7.1-rc (XC) Changelog / November 22, 2014 ==== Important: - After upgrade to v7.1-rc downgrades to v7.0.x will not be possible due to the major firmware differences New: - New: airMAX AC PTMP support - New: Completely new WEB UI design and new features: * TEST mode * airView support (runs without breaking wireless connection) * Ambient Noise diagram * Constellation diagram * CINR histogram * Ethernet cable diagnostics tool * Max Rate selection * LAN speed configuration * Traffic shaping 7.0.3-u1 (XC) Changelog / October 3, 2014 ==== Fixes: - Fix: Stability issues when passing prioritised traffic - Fix: Improved performance for long distance 10MHz/30MHz channel bandwidth links - Fix: Disable Ethernet pause frames 7.0.3 (XC) Changelog / August 18, 2014 ==== New: - New: AC product models support Fixes: - Fix: Traffic issues/increased latency on long distance links - Fix: After Site Survey, some statistics are gone - Fix: Unify 30MHz channel list for US/Puerto Rico and Canada Improvements: - Various stability improvements 7.0.2-u1 (XC) Changelog / July 22, 2014 ==== New: - New: AC product models support - New: Opened more channel width options (10MHz/30MHz) Improvements: - WEB UI improvements/extended statistics reporting/instant configuration changes - Quicker WPA2 connection establishment 7.0.1-u1 (XC) Changelog / June 19, 2014 ==== New products support, XC product family: - New: Rocket 5AC Lite support - New: PowerBeam 5AC 500 support This FW supports PTP mode only.